Flotron: Holding Fixtures




	200 SERIES

	300 & 400 SERIES

	500 SERIES

	600 SERIES

	700 SERIES

	800 SERIES

	900 SERIES

	1000 SERIES

	1100 SERIES

	1200 SERIES

	CUSTOM MODELS

	OVERVIEW TABLE

XD759DB-HYD Data Sheet

The Model XD759DB-HYD-J2-IND15-P8-B078 shown below is typical and representative of the XD759DB-HYD Models. For more information on specifying a holding fixture, see the 700 SERIES OPTIONS page and 700 SERIES CREATING A MODEL NUMBER pdf.

Click for larger image

The maximum distance between mounting interfaces is directly related to the main beam length. Specify the distance between mounting interfaces to be at or slightly larger than the length of the part-to-be-handled. The fixture can be adjusted to accommodate smaller length parts, however, the main beam(s) extending from each end frame may be inconvenient. For more information see the 700 SERIES OPTIONS page and 700 SERIES CREATING A MODEL NUMBER pdf.

Addition of the optional SR or DR gearbox decreases the vertical riser adjustment from 11.8" to 9.8" and increases the minimum trunnion height from 46.9" to 48.9".

A smaller than standard swing radius may be recommended for some applications. See the "Technical Section" under "Holding Fixture Safety" on page 3 of 7 concerning "Unexpected Accident Loads" and the chart on page 4 of 7 referring to "Maximum Recommended Swing Radius"

* Note: Adjusting unit to dimensions smaller than 49" can cause tip over due to small footprint.

Product Features:

Safety Factor: 3
Rated Load Capacity:
Dynamic, 0" eccentricity: 800 lbs. (363 kg.)
Dynamic, 5" eccentricity: 800 lbs. (363 kg.)
Note: The hydraulic cylinders are single acting and a minimum load of 150 lbs is recommended to activate the return (compression) stroke and to give good synchronization of the risers.
Operating Temperature: +32 to +104 °F (0 to +40 °C)
Contact factory for special applications with extended operating temperatures.
Choice of Trunnion Interface/Mount/Clamp Options:
Angle Interface
Mounting Plate Interface
Synchronized Hydraulic Risers
The hydraulic risers can adjust the height of the part-to-be-handled while it is attached to the trunnion interfaces. Turning the pump crank clockwise or counter-clockwise causes the risers to raise or lower in unison.
Choice of Main Beam Length
Main Beam Ball Lock Pin: Reliably prevents End Frames from slipping on Main Beam
Gearbox: 60:1 ratio with 12" diameter crank
Casters: 5" diameter x 2" wide wheel with polyurethane tread, sealed swivel bearing and Tech-lock brake
Materials: Steel construction
Finish: Blue Paint or Powder Coat (at manufacturer's discretion), with selected parts zinc plated. Other finishes available upon request
Trunnion Brake Knob
Price Range: $15K - $33K

Click for larger image

Optional Main Beam Lengths
Optional Trunnion Interface/Mount/Clamp
Optional Index Plate
Optional Index Stops
Optional Casters
Optional Leveling Jacks
Optional Gearboxes incorporating heavy duty, low backlash and stairstep resistant features
Optional finishes for clean room compatibility
Optional Ground Lug and Drag Chain for use in electrostatically protected areas (EPA's)
For more about 700 Series Options click here

All data presented is based on no modifications to the product.

As Flotron is constantly improving products and methods of manufacturing, we reserve the right to modify and/or change design or specifications without notice. Please contact Flotron for verification of critical dimensions and specifications.

For 700 Series - Creating a Model Number pdf click here. - Note: viewing this document requires Adobe's Acrobat Reader.

For clarification of terms or phrases, please see the Holding Fixtures Definitions page.




			Product Features

			700 Series Options

			Holding Fixture Definitions


			XD759DB-HYD
			Dynamic Loading Chart


			700 SERIES Creating A Model Number ( 13.9KB )