Flotron: Holding Fixtures




	200 SERIES

	300 & 400 SERIES

	500 SERIES

	600 SERIES

	700 SERIES

	800 SERIES

	900 SERIES

	1000 SERIES

	1100 SERIES

	1200 SERIES

	CUSTOM MODELS

	OVERVIEW TABLE

800 Series Standard Options:

Optional Main Beam Lengths (BXXX):
Main Beams may be ordered in any length between Trunnion Interface Mounts within the limits shown below. "XXX" = length in inches between trunnion interface mounts (1" increments).

MODEL	MIN	MAX
848	51"	371"
860	51"	371"
872	60"	380"

Lengths longer than MAX shown above require a special beam.

While the two End Frames can be adjusted toward each other to accommodate smaller length parts, excessively long beams with a small part will leave the Main Beams extending from each End Frame enough to be inconvenient. It therefore is desirable to order the main beam close to the size of the actual part-to-be-handled.

Standard Combination Mounting Plate / Angle Clamp (P12 / A30):

Angle Interface (A30) - The Angle Interface offers the most adaptability for customers. Either of the perpendicular surfaces of the angle may be bolted or clamped to. The standard length is 30 inches with no bolt holes. The standard finish is clear zinc plate. The A30 Angle is bolted to the P12 Mounting Plate and may be removed if the customer desires to mount directly to the P12.
Mounting Plate Interface (P12) - The Part-to-be-handled can be easily bolted to this flange type interface. The standard size is 8" x 12" with an eight-hole bolt pattern spaced at 10.5" x 6" centered on the plate. The eight holes will accept up to ½" diameter bolts. The standard finish is clear zinc plate.

Index Plate shown with mounting plate interface

Optional Index Plate (INDSXX):
The standard Index Plate is indexed @ 15 degree increments to prevent trunnion rotation with a lock pin. Optional Index Plates can be supplied at special increments as required by the customer. The two Index Stops can be bolted into any of the index holes in the Index Plate to prevent rotation beyond a desired point. This is desirable if your part-to-be-handled has a protrudance that could hit the main beam or floor or other obstacle when rotated beyond a certain orientation.

Optional Leveling Jacks (J0, J5):
4 bolt-on Leveling Jacks allow for leveling of load while in a stationary position. Code J0, which is not shown, is for jack mounting plates only but does not include Jacks. The J0 option allows for future addition of Jacks. Code J5 is for Jacks which have a hex driver, and uses a standard wrench (not supplied) to crank up or down. The Jacks have 1" of rise for each 10 turns of the hex drive.

JACK has 2.0" (5.08cm) nominal ground clearance when retracted and 3.5" (8.89cm) nominal raise when extended.

Optional Fixture Finishes (N), (C):

Electroless nickel plating (N): This option replaces all zinc-plated parts with either electroless nickel-plated parts or stainless steel parts.
Clean Room option (C): This option is identical to the (N) option but with the addition of electroless nickel-plating on the interior of the end frame slide tubes and vertical support tubes. The exterior of the gearbox as well as the exterior of the end frames are painted with high gloss urethane or epoxy paint in place of the standard textured enamel paint.

Optional Ground Lug and Drag Chain (E):
For use in electrostatically protected areas (EPA's). Proper electrostatic discharge (ESD) grounding of the fixture must be a part of the overall EPA design (See technical section discussion on ESD)

Special Options:
If a standard Holding Fixture does not meet your requirements, contact FLOTRON about custom modifications. Often minor modifications to a standard unit are all you will need and can be done cost efficiently. For a Specifications Sheet, which will aid you in determining special options, click here.

For 800 Series - Creating a Model Number, click here.*

*Note: viewing these documents require Adobe's Acrobat Reader.
For clarification of terms or phrases, please see the Holding Fixtures Definitions page.

All data presented is based on no modifications to the product.

As Flotron is constantly improving products and methods of manufacturing, we reserve the right to modify and/or change design or specifications without notice. Please contact Flotron for verification of critical dimensions and specifications.

Back to 800 Series Product Line




			Holding Fixture Definitions


			800 SERIES Creating A Model Number ( 13.9KB )