Flotron: Holding Fixtures




	200 SERIES

	300 & 400 SERIES

	500 SERIES

	600 SERIES

	700 SERIES

	800 SERIES

	900 SERIES

	1000 SERIES

	1100 SERIES

	1200 SERIES

	CUSTOM MODELS

	OVERVIEW TABLE

300 Series Standard Options:

Optional Main Beam Lengths (B XXX):
Main Beams may be ordered in any length from 26" to 104" between Trunnion Interface Mounts. Above 104" requires special beams. Below 26" can be dangerous due to tip over. "XXX" = length in inches between Trunnion Interface Mounts. (1" increments)

While the two End Frames can be adjusted toward each other to accommodate smaller length parts, excessively long beams with a small part will leave the Main Beams extending from each End Frame enough to be inconvenient. It therefore is desirable to order this Main Beam close to the size
of the actual part-to-be-handled.

Optional Telescopic Main Beams (TB):
Telescopic Main Beams adjust from 62" to 110" between Trunnion Interface Mounts (and 56" to 104" on HD fixtures). They will do this without extending beyond the End frames. They can be adjusted down to 26" between Interface mounts by letting them extend beyond the End frames.

Optional Trunnion Interface/Mount/Clamp:

Angle Interface (SA10) - The Angle Interface offers the most adaptability for customers. Either of the 2" perpendicular surfaces of the angle may be bolted or clamped to. The standard length is 10 inches with no bolt holes. The standard finish is clear zinc plate.

Mounting Plate Interface (1018) - The part-to-be-handled can be easily bolted to this flange type interface. The standard size is 2" by 12.5" with a slotted-hole bolt pattern centered on the plate. The four holes will accept up to ¼" diameter bolts. The standard finish is clear zinc plate.

Board Clamp Interface (1023) - The Board Clamp Interface is a 10" long 2" x 2" angle with two screws clamps. It is very convenient for harness boards and similar shaped loads.

Optional Index Plate (IND15):
Indexed @ 15° increments to prevent trunnion rotation with a lock pin. An Index plate can be supplied with either of the mounting interfaces, shown below or the SA10 angle interface. NOTE: Addition of an optional index plate decreases the vertical adjustment from 12" to 8".

Optional Casters:

Standard Series 1 swivel caster (-5) - Metal sidelock brake and 5" diameter x 7/8" wide Performa wheel
Optional heavy duty Series 2 swivel caster with Side-lock brake (C5SPX)
Optional heavy duty Series 2 swivel caster with total lock brake (C5TL)
Optional heavy duty Series 2 swivel caster with conductive wheel (C5EX)

Optional Fixture Finishes for use in Clean Room (C):
The fixture is supplied with most surfaces electroless nickel plated and miscellaneous hardware made of stainless steel.

Optional Ground Lug and Drag Chain (E):
For use in electrostatically protected areas (EPA's). Proper electrostatic discharge (ESD) grounding of the fixture must be part of the overall EPA design. (See Technical section discussion on ESD.

Special Options:
If a standard holding fixture does not meet your requirements, contact FLOTRON about custom modifications. Often, minor modifications to a standard unit are all you will need and can be done cost effectively. For 300 Series - Creating a Model Number, click here.*

*Note: viewing these documents require Adobe's Acrobat Reader.

For clarification of terms or phrases, please click on the Definitions button.

All data presented is based on no modifications to the product.

As Flotron is constantly improving products and methods of manufacturing, we reserve the right to modify and/or change design or specifications without notice. Please contact Flotron for verification of critical dimensions and specifications.

Back to 300 Series Product Line




			Angle Interface

			Mounting Plate Interface

			Board Clamp Interface

			Scissors Clamp Interface

			Optional Index Plate

			Optional Casters

			Holding Fixture Definitions


			SA10 Angle Interface

			1018 Mounting Plate Interface

			1023 Board Clamp Interface

			IND15 Optional Index Plate

			Optional Casters


			300 SERIES Creating A Model Number ( 12.9KB )